barcodeaddin.com

Click on the Apply button to keep any changes made on this page. in Software Include Code 3 of 9 in Software Click on the Apply button to keep any changes made on this page.




How to generate, print barcode using .NET, Java sdk library control with example project source code free download:
Click on the Apply button to keep any changes made on this page. using barcode generator for software control to generate, create 3 of 9 image in software applications. Radio-frequency identification [ 153 ]. Download at Boykma.Com Connecting to the World with sipXecs Supplementary Services Supplementary Serv barcode 3/9 for None ices are calling services that are provided by User Agents (UA). With SIP, much of the call handling is done by the intelligent end points instead of the PBX. Clicking on the Supplemenary Services menu item will display the following page:.

The following conf iguration options are available on this page (click on Show Advanced Settings to reveal all options): Enable Call Hold: This allows the gateway to enable the "Call Hold" function. The default is enabled (checked). Call Hold Signaling Method: "Call Hold" can be signaled to another UA in a couple of different ways with the AudioCodes gateway.

The connection IP address in SDP is 0.0.0.

0 (default) or "Send Only" where the last attribute of the SDP contains "a=sendonly". Enable Transfer: Enables the "Call Transfer" feature in the gateway. The default is enabled (checked).

Enable Call Waiting: Enables the "Call Waiting" feature in the gateway. The default is disabled (unchecked)..

[ 154 ]. Download at Boykma.Com 6 . Hook-Flash Code: D etermines a digit pattern that, when received from the Telecom side, indicates a "Hook-Flash Code". The valid range is a 25-character string. The default is blank (don"t look for hook flash from the Telecom side).

. Click on the Apply button to keep any changes made on this page. The FXO settings p age (shown as follows) allows some tuning of the interface with the telecommunications provider.. The following conf 39 barcode for None iguration options are available on this page (click on Show Advanced Settings to reveal all options): Waiting for Dial Tone: When an outgoing call is made, the gateway waits to hear the dial tone on the line before dialing. The default is enabled (checked). Time to Wait before Dialing [msec]: After the gateway goes off-hook to dial out, it will wait for this amount of time before dialing the phone number.

The default setting is 1000 milliseconds (1 second).. [ 155 ]. Download at Boykma.Com Connecting to the World with sipXecs Ring Detection Tim USS Code 39 for None eout [seconds]: Ring Detection Timeout is used in conjunction with inbound caller ID detection. If Caller ID is enabled, then the FXO gateway seizes the line after detection of the second ring signal (allowing detection of caller ID, sent between the first and the second rings). If the second ring signal doesn"t arrive for Ring Detection Timeout, the gateway doesn"t initiate a call to IP.

The default setting is 8 seconds. Reorder Tone Duration [seconds]: Before releasing the line, FXO gateway plays a "Busy" or "Reorder" tone, which has duration in seconds. The default is 0 seconds disabling the reorder tone.

Answer Supervision: If this is enabled (checked), the FXO gateway sends a SIP 200 OK (to INVITE) messages when speech/fax/modem is detected. If it is disabled, a SIP 200 OK is sent immediately after the FXO gateway finishes dialing. The default setting is disabled (unchecked).

Rings before Detecting Caller ID: Determines the number of rings to wait for the caller ID from the phone company. The default is 1 ring. Send Metering Message to IP: Sends a metering tone INFO message to the IP of 12/16 kHz metering pulse.

Not used by sipXecs, so the default is disabled (unchecked). Disconnect on Busy Tone: If the gateway detects a busy tone it will interpret this as a disconnect signal and hang up the line. The default is enabled (checked).

Enable Call Disconnect on Dial Tone: If the gateway detects a dial tone on the phone line, it will interpret this as a disconnect signal and hang up the line. The default is enabled (checked). Guard Time Between Calls: Sometimes, after a call is ended and the gateway goes on-hook, a delay is required before placing a new call (and performing the subsequent off-hook).

This is necessary to prevent the phone company thinking that the gateway is trying to perform a hook-flash. The default is 1 second. First Default Caller ID: The value that is displayed for incoming calls when no caller ID information is available.

The gateway will add a port identification suffix. The default value is set to "Unknown"..

Copyright © barcodeaddin.com . All rights reserved.